Form OP-UA29 (TCEQ-10049) "Glass Manufacturing Unit Attributes" - Texas

What Is Form OP-UA29 (TCEQ-10049)?

This is a legal form that was released by the Texas Commission on Environmental Quality - a government authority operating within Texas. As of today, no separate filing guidelines for the form are provided by the issuing department.

Form Details:

  • Released on December 1, 2015;
  • The latest edition provided by the Texas Commission on Environmental Quality;
  • Easy to use and ready to print;
  • Quick to customize;
  • Compatible with most PDF-viewing applications;
  • Fill out the form in our online filing application.

Download a printable version of Form OP-UA29 (TCEQ-10049) by clicking the link below or browse more documents and templates provided by the Texas Commission on Environmental Quality.

ADVERTISEMENT
ADVERTISEMENT

Download Form OP-UA29 (TCEQ-10049) "Glass Manufacturing Unit Attributes" - Texas

Download PDF

Fill PDF online

Rate (4.6 / 5) 18 votes
Texas Commission on Environmental Quality
Form OP-UA29
Glass Manufacturing Unit Attributes
General:
This form is used to provide a description and data pertaining to all glass manufacturing units with potentially applicable
requirements associated with a particular regulated entity number and application. Each table number, along with the
possibility of a corresponding letter (i.e., Table 1a, Table 1b), corresponds to a certain state or federal rule. If the rule on
the table is not potentially applicable to a glass manufacturing unit, then it should be left blank and need not be submitted
with the application. If the codes entered by the applicant show negative applicability to the rule or sections of the rule
represented on the table, then the applicant need not complete the remainder of the table(s) that corresponds to the rule.
Further instruction as to which questions should be answered and which questions should not be answered are located in
the “Specific” section of the instruction text. The following is included in this form:
Table 1:
Title 40 Code of Federal Regulations Part 60 (40 CFR Part 60)
Subpart CC: Standards of Performance for Glass Manufacturing Plants
The Texas Commission on Environmental Quality (TCEQ) Regulated Entity Number (RNXXXXXXXXX) and the
application area name from Form OP-1 (Site Information Summary) must appear in the header of each page for the
purpose of identification for the initial submittal. The date of the initial form submittal must also be included and should
be consistent throughout the application (MM/DD/YYYY). Leave the permit number blank for the initial form
submittal. If this form is included as part of the permit revision process, enter the permit number assigned by the TCEQ,
the area name (from Form OP-1), the date of the revision submittal, and the regulated entity number.
Unit attribute questions that do not require a response from all applicants are preceded by qualification criteria in the
instructions. If the unit does not meet the qualification criteria, a response to the question is not required. Anytime a
response is not required based on the qualification criteria, leave the space on the form blank.
Notwithstanding any qualification criteria in the form instructions or information provided in other TCEQ
guidance, the applicant may leave an attribute question blank (or indicate “N/A” for “Not Applicable”) if the
attribute is not needed for the applicable requirement determinations of a regulation for a unit.
In some situations, the applicant has the option of selecting alternate requirements, limitations, and/or practices for a unit.
Note that these alternate requirements, limitations, and/or practices must have the required approval from the TCEQ
Executive Director and/or the U.S. Environmental Protection Agency (EPA) Administrator before the federal operating
permit application is submitted.
The Texas Commission on Environmental Quality (TCEQ) requires that a Core Data Form be submitted on all incoming
registrations unless all of the following are met: the Regulated Entity and Customer Reference Numbers have been issued
by the TCEQ and no core data information has changed. The Central Registry, a common record area of the TCEQ,
maintains information about TCEQ customers and regulated activities, such as company names, addresses, and telephone
numbers. This information is commonly referred to as “core
TCEQ - 10049 (APDG 5172v8, Revised 12/15) OP-UA29
This form is for use by facilities subject to air quality permit
requirements and may be revised periodically. (Title V Release 11/04)
Page 1 of 3
Texas Commission on Environmental Quality
Form OP-UA29
Glass Manufacturing Unit Attributes
General:
This form is used to provide a description and data pertaining to all glass manufacturing units with potentially applicable
requirements associated with a particular regulated entity number and application. Each table number, along with the
possibility of a corresponding letter (i.e., Table 1a, Table 1b), corresponds to a certain state or federal rule. If the rule on
the table is not potentially applicable to a glass manufacturing unit, then it should be left blank and need not be submitted
with the application. If the codes entered by the applicant show negative applicability to the rule or sections of the rule
represented on the table, then the applicant need not complete the remainder of the table(s) that corresponds to the rule.
Further instruction as to which questions should be answered and which questions should not be answered are located in
the “Specific” section of the instruction text. The following is included in this form:
Table 1:
Title 40 Code of Federal Regulations Part 60 (40 CFR Part 60)
Subpart CC: Standards of Performance for Glass Manufacturing Plants
The Texas Commission on Environmental Quality (TCEQ) Regulated Entity Number (RNXXXXXXXXX) and the
application area name from Form OP-1 (Site Information Summary) must appear in the header of each page for the
purpose of identification for the initial submittal. The date of the initial form submittal must also be included and should
be consistent throughout the application (MM/DD/YYYY). Leave the permit number blank for the initial form
submittal. If this form is included as part of the permit revision process, enter the permit number assigned by the TCEQ,
the area name (from Form OP-1), the date of the revision submittal, and the regulated entity number.
Unit attribute questions that do not require a response from all applicants are preceded by qualification criteria in the
instructions. If the unit does not meet the qualification criteria, a response to the question is not required. Anytime a
response is not required based on the qualification criteria, leave the space on the form blank.
Notwithstanding any qualification criteria in the form instructions or information provided in other TCEQ
guidance, the applicant may leave an attribute question blank (or indicate “N/A” for “Not Applicable”) if the
attribute is not needed for the applicable requirement determinations of a regulation for a unit.
In some situations, the applicant has the option of selecting alternate requirements, limitations, and/or practices for a unit.
Note that these alternate requirements, limitations, and/or practices must have the required approval from the TCEQ
Executive Director and/or the U.S. Environmental Protection Agency (EPA) Administrator before the federal operating
permit application is submitted.
The Texas Commission on Environmental Quality (TCEQ) requires that a Core Data Form be submitted on all incoming
registrations unless all of the following are met: the Regulated Entity and Customer Reference Numbers have been issued
by the TCEQ and no core data information has changed. The Central Registry, a common record area of the TCEQ,
maintains information about TCEQ customers and regulated activities, such as company names, addresses, and telephone
numbers. This information is commonly referred to as “core
TCEQ - 10049 (APDG 5172v8, Revised 12/15) OP-UA29
This form is for use by facilities subject to air quality permit
requirements and may be revised periodically. (Title V Release 11/04)
Page 1 of 3
OP-UA29 Instructions
data.” The Central Registry provides the regulated community with a central access point within the agency to check core
data and make changes when necessary. When core data about a facility is moved to the Central Registry, two new
identification numbers are assigned: the Customer Reference (CN) number and the Regulated Entity (RN) number. The
Core Data Form is required if facility records are not yet part of the Central Registry or if core data for a facility has
changed. If this is the initial registration, permit, or license for a facility site, then the Core Data Form must be completed
and submitted with application or registration forms. If amending, modifying, or otherwise updating an existing record for
a facility site, the Core Data Form is not required, unless any core data information has changed. To review additional
information regarding the Central Registry, go to the TCEQ Web site at www.tceq.texas.gov/permitting/central_registry.
Specific:
Table 1:
Title 40 Code of Federal Regulations Part 60 (40 CFR Part 60)
Subpart CC: Standards of Performance for Glass Manufacturing Plants
Unit ID No.: Enter the identification number (ID No.) for the glass melting device (maximum 10 characters) as listed on
Form OP SUM (Individual Unit Summary).
SOP Index No.: Site operating permit (SOP) applicants should indicate the SOP index number for the unit or group of
units (maximum 15 characters consisting of numeric, alphanumeric characters, and/or dashes prefixed by a code for the
applicable regulation [i.e., 60KB-XXXX]). For additional information relating to SOP index numbers, please refer to the
TCEQ website at www.tceq.texas.gov/assets/public/permitting/air/Guidance/Title_V/sop_initial.pdf.
Facility Type: Select one of the following options for the facility type. Enter the code on the form.
Code
Description
G4550-
Glass melting furnace as defined in 40 CFR Part 60, Subpart CC with a design capacity of less
than 4550 kg/day
G4550+
Glass melting furnace as defined in 40 CFR Part 60, Subpart CC with a design capacity of greater
than or equal to 4550 kg/day
HAND
Hand glass melting furnace as defined in 40 CFR Part 60, Subpart CC
ELECT
All electric melter
Code
Description
EXPER
Experimental furnace
Continue only if “Facility Type” is “G4550+” or “EXPER.”
Construction/Modification Date: Select one of the following options that describes the date of commencement of the
most recent construction, modification, or reconstruction. Enter the code on the form.
Note: Construction, modification, or reconstruction shall include those activities other than rebricking or converting to
the use of liquid fuel.
Code
Description
79-
On or before June 15, 1979
79+
After June 15, 1979
Continue only if “Construction/Modification Date” is “79+.”
TCEQ - 10049 (APDG 5172v8, Revised 12/15) OP-UA29
This form is for use by facilities subject to air quality permit
requirements and may be revised periodically. (Title V Release 11/04)
Page 2 of 3
OP-UA29 Instructions
Modified Process: Enter “YES” if the affected facility is a modified process glass-melting furnace. Otherwise,
enter “NO.”
Complete “Simultaneous Firing” only if “Facility Type” is “G4550+.”
Simultaneous Firing: Enter “YES” if the furnace simultaneously fires gaseous and liquid fuels. Otherwise, enter “NO.”
Continue only if “Modified Process” is “YES.”
Complying with § 60.292: Enter “YES” if choosing to comply with the provisions of 40 CFR § 60.292. Otherwise,
enter “NO.”
Continue only if “Complying with § 60.292” is “NO.”
Glass Recipe/Product: Select one of the following options for the glass recipe or the product produced by the glass
melting furnace. Enter the code on the form.
Code
Description
SODA
Soda-lime recipe for container, flat, pressed and blown glass
BORO
Borosilicate recipe for pressed or blown glass
FIBER
Wool fiberglass and/or textile fiberglass
Complete “ACMS” and “ACMS ID No.” only if “Glass Recipe/Product” is “SODA.”
ACMS: Enter “YES” if an alternate continuous monitoring system (ACMS) has been approved by the EPA
Administrator. Otherwise, enter “NO.”
ACMS ID No.: If an ACMS has been approved, then enter the corresponding ACMS unique identifier
(maximum 10 characters) for each unit or process. If the unique identifier is unavailable, then enter the date of the ACMS
approval letter. The unique identifier and/or the date of the approval letter is contained in the compliance file under the
appropriate regulated entity number. Otherwise, leave this column blank.
Continue only if “ACMS” is “NO” or if “Glass Recipe/Product” is “BORO” or “FIBER.”
Opacity Confidence Level: Enter “YES” if the opacity confidence level is to be redetermined. Otherwise, enter “NO.”
TCEQ - 10049 (APDG 5172v8, Revised 12/15) OP-UA29
This form is for use by facilities subject to air quality permit
requirements and may be revised periodically. (Title V Release 11/04)
Page 3 of 3
Texas Commission on Environmental Quality
Glass Manufacturing Unit Attributes
Form OP-UA29 (Page 1)
Federal Operating Permit Program
Table 1: Title 40 Code of Federal Regulations Part 60 (40 CFR Part 60)
Subpart CC: Standards of Performance for Glass Manufacturing Units
Date:
Permit No.:
Regulated Entity No.:
Area Name:
Customer Reference No.:
Construction/
Glass
Opacity
Facility
Modified
Simultaneous
Complying
Unit ID No.
SOP Index No.
Modification
Recipe/
ACMS
ACMS ID No.
Confidence
Type
Process
Firing
with § 60.292
Date
Product
Level
TCEQ - 10049 (APDG 5172v8, Revised 12/15) OP-UA29
This form is for use by facilities subject to air quality permit
requirements and may be revised periodically. (Title V Release 11/04)
Page _____ of _____